Confining effect on the bearing capacity of circular footings on a purely cohesive soilEffet du confinement sur la capacité portante d'une fondation circulaire sur un sol purement cohérent

The bearing capacity of axially symmetrical footings acting on a purely cohesive soil foundation contained by a rigid wall at a finite distance is investigated within the framework of the Yield design theory. Following the same tracks as in a preceding paper devoted to strip footings, the analysis is performed by referring to already existing results concerning the bearing capacity of a circular footing on a soil layer with limited thickness. It comes out that the bearing capacity factor determined by Eason and Shield for a rough circular footing on an unlimited soil foundation is increased by a correction factor that increases when the diameter of the container decreases. Comparison with the results obtained for strip footings acting on a purely cohesive soil in the same conditions shows that the confining effect is significantly lower for a circular footing than for a strip footing. To cite this article: J. Salençon, C. R. Mecanique 330 (2002) 521–525.     

Application of X-ray diffraction, micromagnetic and hole drilling methods for residual stress determination in a ball bearing steel ring

A basic understanding of distortion problems requires the analysis of a complete manufacturing process including an almost complete overview of residual stress states in the component during each production step. To reduce the measurement time in the future, three measurements methods (X-ray diffraction, micromagnetic and blind hole drilling methods) have been used to analyze residual stress states in machined AISI 52100 ball bearing rings. X-ray diffraction was used as a state-of-the-art method for machining induced residual stresses with pronounced gradients. The ring exhibited a complex residual stress state with high tensile residual stresses at the surface, a strong gradient in depth, and also showed some variation along the outer circumference due to a superimposition of machining induced residual stresses and effects from the clamping device process. Due to this surface state, micromagnetic signals depend on the analyzing frequency. A calibration of the signals was only possible with the X-ray diffraction data. The results of the three different measurement methods correlate reasonably well.     

基于振动监测的静载荷滑动轴承接触摩擦故障诊断实验研究

采用静载荷滑动轴承试验台模拟轴颈-轴承从液体润滑状态逐步向干摩擦状态过渡时的接触摩擦故障的发生和发展过程,进而利用振动信号诊断滑动轴承的接触摩擦故障;通过对特征参数进行归一化处理得到无量纲特征参数,进而通过无量纲特征参数的适当数学组合得到无量纲诊断准则,并探讨了无量纲诊断准则的适用性.结果表明:利用所得到的无量纲诊断准则进行轴颈-轴承接触摩擦故障诊断时无须建立用于模式识别的标准模,可实现快捷方便的故障诊断;无量纲诊断准则对工况不敏感,而对故障更敏感,适用于可变工况下滑动轴承的故障诊断,且诊断成本较低.     

氮化铁磁性流体密封研究

利用磁性流体被磁场吸附的原理，探讨了氮化铁磁性流体密封装置的设计原理和动作过程，分析并通过试验验证了磁性流体密封承压能力，进而成功地研制了氮化铁磁性流体密封安全阀，基于磁性流体密封安全阀开启压力稳定性、可控性和密封性能测试结果，所研制的样机已正常运行10000h。     

径向轴承启动过程瞬态热效应的研究

联立求解广义雷诺方程、油膜瞬态三维能量方程、轴瓦瞬态三维固体热传导方程及轴颈的运动方程，并考虑粘度和密度随温度及压力的变化，在油膜与轴瓦界面使用热流连续性边界条件，确定了在承受稳态载荷时圆轴承在启动过程中的温度变化情况．介绍了一种有效的用于求解轴承瞬态性能的改进Newton—Raphson算法．结果表明：整个系统达到热平衡的时间与启动加速度的大小无关；启动加速度越高，温度升高越快；在启动过程中，油膜最高温度出现的位置沿膜厚方向而变化．同有关试验结果的对比证实所建模型和所用算法正确可行．     

对数凸型滚针凸度量设计的新方法

本文利用三维有限长弹性接触问题的数值解法分析了实体套圈滚针轴承中的越程槽结构因素对对数凸型滚针接触压力分布的影响。结果表明,套圈上的越程槽宽度是确定滚针最佳凸度量时应考虑的一个重要因素。据此给出了对数凸型滚针凸度量设计的新方法。该方法可用于各种结构形式滚针轴承的滚针凸度量设计。     

Percolation theory approach to transport phenomena in porous media

The percolation theory approach to static and dynamic properties of the single- and two-phase fluid flow in porous media is described. Using percolation cluster scaling laws, one can obtain functional relations between the saturation fraction of a given phase and the capillary pressure, the relative permeability, and the dispersion coefficient, in drainage and imbibition processes. In addition, the scale dependency of the transport coefficient is shown to be an outcome of the fractal nature of pore space and of the random flow pattern of the fluids or contaminant.     

非牛顿流体有限长粗糙轴承分析

本文采用H.Christense力提出的随机粗糙模型,推导了幂律型流体纵向粗糙型和横向粗糙型润滑雷诺方程和相应的承载力、流量系数和摩擦系数的计算公式.对有限长动载径向轴承纵向粗糙型雷诺方程,用差分方法进行数值求解,得到了粗糙度和幂律指数对轴承的压力分布、承载力、流量系数和摩擦系数影响曲线,并有表面粗糙度和润滑油的非牛顿特性独立地影响轴承油膜力学特性的结论.     

水泥土搅拌桩复合地基承载力公式中折减系数β取值的分析

水泥土搅拌桩复合地基承载力设计公式中的桩间土承载力折减系数 β值需根据经验确定,且取值范围较大。因此,要准确计算出复合地基承载力有一定难度。本文根据桩土共同作用机理,探讨了折减系数 β的各种影响因素。在比较研究了一些典型工程静载试验的实测资料之后,对系数 β的取值作了具体分析并给出了合理的建议值。     

Crankshaft-bearing evolution indexes investigation and asperity contact identification based on neural network

The dynamic and lubrication characteristic analyses of the crankshaft–bearing system is quite a complex problem, and it is important to avoid asperity contact which may lead to bearing wear and increase of friction loss significantly in dynamic lubrication condition. In this paper, the dynamic characteristic that has an essential impact on lubrication was investigated over an inline six-cylinder engine. Multi-body dynamics method, tribology, finite element method (FEM), finite difference method (FDM) and component mode synthesis method (CMS) were combined to analyze the dynamic characteristic of crankshaft, oil leakage, oil film pressure, asperity contact pressure and friction loss. Then the orthogonal experiment that included 5 levels and 6 factors was conducted to obtain the training sample sets for neural network, and the probabilistic neural network (PNN) was employed to identify weather the asperity contact happened or not according to its nonlinear characteristic. The analyses which can provide the guidance for the design of main bearing, and avoid the asperity contact in the lubrication are significant to the design of the bearing at the development stage of the engine.